AY Honors/Welding/Requirements/en - Revision history

FuzzyBot: Updating to match new version of source page

2023-03-21T15:00:46Z

Updating to match new version of source page

FuzzyBot: Updating to match new version of source page

2023-03-20T13:22:48Z

Updating to match new version of source page

Show changes

FuzzyBot: Updating to match new version of source page

2023-03-17T22:08:11Z

Updating to match new version of source page

FuzzyBot: Updating to match new version of source page

2023-01-02T14:07:24Z

Updating to match new version of source page

FuzzyBot: Updating to match new version of source page

2022-07-21T19:38:37Z

Updating to match new version of source page

FuzzyBot: Updating to match new version of source page

2021-08-01T00:23:13Z

Updating to match new version of source page

New page

{{HonorSubpage}}

<section begin=Body />

<b>1. <section begin=req1 /><noinclude></noinclude>Identify all parts of the following:
<noinclude></noinclude><section end=req1 /></b>

:<b>a. <section begin=req1a /><noinclude></noinclude>Welding and cutting torches
<noinclude></noinclude><section end=req1a /></b>

:<b>b. <section begin=req1b /><noinclude></noinclude>Oxygen and acetylene gauges and their differences
<noinclude></noinclude><section end=req1b /></b>

:<b>c. <section begin=req1c /><noinclude></noinclude>Oxygen and acetylene hoses and their differences
<noinclude></noinclude><section end=req1c /></b>

:<b>d. <section begin=req1d /><noinclude></noinclude>Oxygen and acetylene tanks and their differences
<noinclude></noinclude><section end=req1d /></b>

<b>2. <section begin=req2 /><noinclude></noinclude>Explain the safe working pressures of oxygen and acetylene, as per your instructor's directions, for various procedures.
<noinclude></noinclude><section end=req2 /></b>

<b>3. <section begin=req3 /><noinclude></noinclude>While blindfolded, demonstrate ability to hook up an entire oxyacetylene kit, including tanks, gauges, hoses, and torches, and light the same.**
<noinclude></noinclude><section end=req3 /></b>

<b>4. <section begin=req4 /><noinclude></noinclude>As per your instructor's directions, weld two mild steel test plates (1/8 inch x 1 inch x 8 inches) (0.3 cm x 2.5 cm x 20.3 cm) in horizontal, and vertical positions.
<noinclude></noinclude><section end=req4 /></b>

<b>5. <section begin=req5 /><noinclude></noinclude>Use a cutting torch and demonstrate your skill by making one 12 inches (30.5 cm) straight-line cut, one circle cut of at least 3 inches (7.6 cm) in diameter and one 3 inch (7.6 cm) star cut. The cuts are to be made on mild steel plate at least 1/4 inch (0.6 cm) thick.
<noinclude></noinclude><section end=req5 /></b>

<b>6. <section begin=req6 /><noinclude></noinclude>Demonstrate your ability to braze a cast-iron object with at least 1/4 inch (0.6 cm) double bevel butt weld 2 inches (5 cm) long.
<noinclude></noinclude><section end=req6 /></b>

<b>7. <section begin=req7 /><noinclude></noinclude>Explain the safety precautions and safety equipment normally used in electric welding in relation to eyes, hands, and exposed skin areas. Why should the tank valves never be oiled?
<noinclude></noinclude><section end=req7 /></b>

<b>8. <section begin=req8 /><noinclude></noinclude>Explain the difference between oxyacetylene and electric arc welding.
<noinclude></noinclude><section end=req8 /></b>

<b>9. <section begin=req9 /><noinclude></noinclude>Demonstrate ability to select from an electrode guide the proper amperage and electrode for various types and thicknesses of metal.
<noinclude></noinclude><section end=req9 /></b>

<section begin=challenge />
<b>10. <section begin=req10 /><noinclude></noinclude>Demonstrate ability to weld flat, vertical, horizontal, and overhead on (1/8 inch x 1 inch x 8 inches) (0.3 cm x 2.5 cm x 20.3 cm) mild steel test plates.
<noinclude></noinclude><section end=req10 /></b>
<section end=challenge />

<b>Note: <section begin=reqNote /><noinclude></noinclude>An instructor is a must. Welding is a very critical and serious skill to learn and is not a home-type course. Welding essentially takes the place of bolts and rivets, and if not properly done, is most dangerous. Example: A trailer hitch not properly bonded, or machinery exposed to the strain of pull or weight, is an invitation to disaster.

Note: <nowiki>**</nowiki>This requirement demonstrates one's skill in working in darkness, such as in an emergency. All acetylene connection threads are left-handed, while all oxygen connection threads are right-handed.
<noinclude></noinclude><section end=reqNote /></b>
<section end=Body />

<noinclude>[[Category:Honor Requirements|{{#titleparts:{{PAGENAME}}|1|2}}]]
[[Category:Honor Requirements Revision 3|{{#titleparts:{{PAGENAME}}|1|2}}]]
<noinclude></noinclude>

@@ Line 121: / Line 121: @@
 <noinclude></noinclude><section end=req11 /></b>
-:<b>a. <section begin=req11a /><noinclude></noinclude>PAC: Make one straight cut at least three inches long in mild steel or aluminum
+:<b>a. <section begin=req11a /><noinclude></noinclude>PAC: Make one straight cut at least three inches long in mild steel or aluminum.
 <noinclude></noinclude><section end=req11a /></b>
@@ Line 149: / Line 149: @@
 <section end=challenge />
-<b>Note: <section begin=reqNote /><noinclude></noinclude><nowiki>*</nowiki> Must pass a knowledge exam upon completion. <br>^ These are minimum requirements; additional welding is encouraged
+<b>{{Localize|Note}}: <section begin=reqNote /><noinclude></noinclude><nowiki>*</nowiki> Must pass a knowledge exam upon completion. <br>^ These are minimum requirements; additional welding is encouraged
 <noinclude></noinclude><section end=reqNote /></b>
 <section end=Body />

← Older revision		Revision as of 19:38, 21 July 2022
Line 52:		Line 52:
	<noinclude></noinclude><section end=reqNote /></b>		<noinclude></noinclude><section end=reqNote /></b>
	<section end=Body />		<section end=Body />
−
−	~~<noinclude>[[Category:Honor Requirements\|{{#titleparts:{{PAGENAME}}\|1\|2}}]]~~
−	~~[[Category:Honor Requirements Revision 3\|{{#titleparts:{{PAGENAME}}\|1\|2}}]]~~
−	~~<noinclude></noinclude>~~

@@ Line 47: / Line 47: @@
 <section end=challenge />
-<b>Note: <section begin=reqNote /><noinclude></noinclude>An instructor is a must. Welding is a very critical and serious skill to learn and is not a home-type course. Welding essentially takes the place of bolts and rivets, and if not properly done, is most dangerous. Example: A trailer hitch not properly bonded, or machinery exposed to the strain of pull or weight, is an invitation to disaster.
+<b>{{Localize|Note}}: <section begin=reqNote /><noinclude></noinclude>An instructor is a must. Welding is a very critical and serious skill to learn and is not a home-type course. Welding essentially takes the place of bolts and rivets, and if not properly done, is most dangerous. Example: A trailer hitch not properly bonded, or machinery exposed to the strain of pull or weight, is an invitation to disaster.
 Note: <nowiki>**</nowiki>This requirement demonstrates one's skill in working in darkness, such as in an emergency. All acetylene connection threads are left-handed, while all oxygen connection threads are right-handed.
 <noinclude></noinclude><section end=reqNote /></b>
 <section end=Body />

@@ Line 1: / Line 1: @@
 {{HonorSubpage}}
 <section begin=Body />
 <b>1. <section begin=req1 /><noinclude></noinclude>Identify all parts of the following: